021-39529839
电 话：021-39526589-8004
联系人：覃小敏
手 机：19117262520
地 址： 中国 上海 嘉定区嘉涌路99弄6号713
日本油研叠加阀，YUKEN叠加阀资料
上海乾拓贸易有限公司
企业QQ：2880626087
电话；
手机；（微信）
邮箱；@163.com
地址：上海市嘉定区江桥嘉涌路99弄6号楼713室
Keep all installation holes and clean. Failure to do this may cause fire due t o oil leakage. CAUTION Before installing the product,
be sure all specified bolts are tightened to the specified torque levels.
紧固在规格外的水平可能导致操作不当，损坏，漏油等。
应在清洁的环境条件下按照以下程序进行。
使用先导式止回阀和节流阀和止回阀（出口）时的堆叠顺序。
在图A中的A到T流动图中（不正确），
Tightening to levels outside specifications may cause improper operation, damage, oil leakage, etc.
Assebly should be carried out in clean environment conditions and in accordance with the following procedure.
因此请参考以下堆叠顺序说明。
请注意，当使用模块化堆垛阀设计系统时，
应适当考虑到将来维护的工作空间。
由于这种紧凑的设计，阀门适合狭窄的空间，
因此适用于机床，工作车辆和节省劳力的机器。
These modular valves have the same mounting surface
as those for the DSG-005 solenoid operated directional valves and a uniform thickness.
因此，在组合中需要图示中的堆叠等效（正确）。
应注意确保阀门及其安装面清洁，无污物或其他异物。
参考电路图，堆叠模块化电磁阀和电磁式换向阀，
同时将其O形圈侧朝向安装座，并确保定位销和销槽之间的对应关系。
Instructions Caution in the selection of valves and circuit designing
The selection of modular valves, to suit a particular function or hydraulic circuit,
are made in exactly the same way as conventional valves taking into account of the flow and pressure of each valve to be used.
In some cases, the stacking system may be restricted, so please refer to the following instructions for stacking sequence.
Please note, that when designing a system using modular stacking valves,
部件从安装螺栓套件取下4个螺栓，并以规定的扭矩拧紧。
保持所有安装孔并清洁。
否则可能由于漏油而导致火灾。
这些模块化阀门具有与DSG-005电磁换向阀相同的安装面，厚度均匀。
其中几个可以堆叠并螺栓连接在一起成为液压回路。
and eventually creates an open and shut operation of the valve repeatedly
which may cause the cylinder to have a knocking effect (the same effect will occur in the case of B to T flow).
Therefore, the stacking s equence in the drawing right (correct) is required in this combination. Assembly
Take 4 bolts from the mounting bolt kit and tighter them in the specified torque.
小心在安装产品之前，确保所有指定的螺栓拧紧到指定的扭矩水平。
压力在节气门和止回阀的节流作用的部分被压缩。
所产生的压力用于关闭先导操作的阀，
Several of them can be stacked and bolted together into a hydraulic circuit.
Because of this compactest design, the valves fit in a narrow space,
so they are optimal for machine tools, work vehicles and labor-saving machines.
说明在选择阀门和电路设计时的注意事项选择模块化阀门
以适应特定功能或液压回路的制造方式与传统阀门完全相同，
考虑到要使用的每个阀门的流量和压力。
在某些情况下，堆叠系统可能受到限制，
due consideration should be given to working space for future maintenance.
Stacking sequence when using pilot operated check valves and throttle and check valves (metre-out).
In A to T flow in the drawing left (incorrect), pressure is g enerated at part with a throttle effect of the throttle and check valve.
The pressure so generated acts to shut the pilot operated check valve
并终重复地产生阀的打开和关闭操作，
这可能导致气缸具有爆震效应（在B到T流动的情况下会发生相同的效果） 。日本油研叠加阀，YUKEN叠加阀资料
您是第33111805位访客
公司主营：德国SICK传感器，FESTO比例阀，德国FESTO电磁阀，ASCO电磁阀，NORGREN电磁阀，LEUZE传感器，CKD电磁阀，CKD气缸 沪ICP备09006758号-10
乾拓贸易是销售气缸,继电器的公司,以SMC气缸,PILZ继电器,FESTO气缸为主,产品型号规格齐全,报价合理,可满足不同客户的需求!
版权所有：上海乾拓贸易有限公司
