021-39529839
电 话：028-86751041-8004
联系人：王倩
手 机：15308020014
地 址： 中国 上海 嘉定区嘉涌路99弄6号713
更新时间：2024-12-20 浏览数：34
所属行业：仪器仪表> 阀门> 电磁阀
发货地址：日本
产品规格：--
产品数量：100
包装说明：--
单 价：面议
SMC电磁阀 5通先导阀SY5520-5DZD-01
兼容电缆
线O.D：?3.5到O7
（参考）0.5平方毫米，2核或3核，相当于JIS C 3306
进行连接时，请注意使用比其他
支持的尺寸（?3.5到?7）重型线无法满足IP65
（外壳）的标准。此外，一定要拧紧螺母地面和
拿着自己规定的扭矩范围内螺纹。
分离接线盒和外壳，电源线入口后
可以通过将所述壳体中的所期望的方向来改变
SMC电磁阀 5通先导阀SY5520-5DZD-01
（4个方向以90°的间隔）。
*当装有一盏灯，注意不要损坏光
与电源线的导线。
慎重
1.松开固定螺丝，并拔出插头出来的
电磁阀接线端子。
2.卸下固定螺丝后，将平头螺丝刀，
等插入接线盒底部的凹槽和撬
开，分离终端块和外壳。
3.松开端子上的端子螺丝（一字螺丝）
块，inser吨引线的芯入端子
根据连接方式，并固定在牢固
与终端螺钉。
4.紧固螺母地面固定线。
注意事项
插入并拔出插头没有垂直倾斜到一边。
Connection
Changing the entry direction
Compatible cable
Cord O.D.: ?3.5 to ?7
(Reference) 0.5mm2, 2-core or 3-core, equivalent to JIS C 3306
When making connections, take note that using other than the
supported size (?3.5 to ?7) heavy duty cord will not satisfy IP65
(enclosure) standards. Also, be sure to tighten the ground nut and
holding screw within their specified torque ranges.
After separating the terminal block and housing, the cord entry
can be changed by attaching the housing in the desired direction
(4 directions at 90° intervals).
? When equipped with a light, be careful not to damage the light
with the cord’s lead wires.
Caution
1. Loosen the holding screw and pull the connector out of the
solenoid valve terminal block.
2. After removing the holding screw, insert a flat head screwdriver,
etc. into the notch on the bottom of the terminal block and pry it
open, separating the terminal block and the housing.
3. Loosen the terminal screws (slotted screws) on the terminal
block, inser t the cores of the lead wires into the terminals
according to the connection method, and fasten them securely
with the terminal screws.
4. Secure the cord by fastening the ground nut.
Precautions
Plug in and pull out the connector vertically without tilting to one
Changing the entry direction
Compatible cable
Cord O.D.: ?3.5 to ?7
(Reference) 0.5mm2, 2-core or 3-core, equivalent to JIS C 3306
When making connections, take note that using other than the
supported size (?3.5 to ?7) heavy duty cord will not satisfy IP65
(enclosure) standards. Also, be sure to tighten the ground nut and
holding screw within their specified torque ranges.
After separating the terminal block and housing, the cord entry
can be changed by attaching the housing in the desired direction
(4 directions at 90° intervals).
? When equipped with a light, be careful not to damage the light
with the cord’s lead wires.
Caution
1. Loosen the holding screw and pull the connector out of the
solenoid valve terminal block.
2. After removing the holding screw, insert a flat head screwdriver,
etc. into the notch on the bottom of the terminal block and pry it
open, separating the terminal block and the housing.
3. Loosen the terminal screws (slotted screws) on the terminal
block, inser t the cores of the lead wires into the terminals
according to the connection method, and fasten them securely
with the terminal screws.
4. Secure the cord by fastening the ground nut.
Precautions
Plug in and pull out the connector vertically without tilting to one side.
SMC电磁阀 5通先导阀SY5520-5DZD-01
您是第33141090位访客
公司主营：德国SICK传感器，FESTO比例阀，德国FESTO电磁阀，ASCO电磁阀，NORGREN电磁阀，LEUZE传感器，CKD电磁阀，CKD气缸 沪ICP备09006758号-10
乾拓贸易是销售气缸,继电器的公司,以SMC气缸,PILZ继电器,FESTO气缸为主,产品型号规格齐全,报价合理,可满足不同客户的需求!
版权所有：上海乾拓贸易有限公司
